AC380V 3.5KW/4.5KW/5.5KW/6KW18000rpm 0 300HZ Square High Speed Air cooled Spindle Motor/Engraving Machine/Drilling Machine Parts

AC380V 3.5KW/4.5KW/5.5KW/6KW18000rpm 0 300HZ Square High Speed Air cooled Spindle Motor/Engraving Machine/Drilling Machine Parts
  • Продавецphiladelphiaeaglesvscarolinapanthers.us
  • Список ценUS $391.50piece
  • Продажная ценаUS $391.50piece
  • ДоставкаБесплатная доставка
  • Рейтинги3,8 (915)

Oписание продукта

4.5KW ER32 380V Air-cooled CNC Spindle Motor + 5.5KW 380V VFD inverter Spindle Motor Speed Controller for CNC Router

Package Content:

1 x 4.5kW Spindle Motor 380V

1 x 5.5KW sunfar VFD Variable Frequency Driver

Spindle Motor Specification:

Providing the default Collet ER32 12.7mm, if not please do contact us for a better solution.

Model

GDZ120*103-4.5

Product type

Square High-Speed Motorized Spindle Motor for Woodworking

Brand

Changsheng(Made in China)

Speed

18000rpm

Power

4.5KW

Voltage

380V

Current

9.5A

Frequency

300Hz

Collet

ER32 12.7mm default

Lubrication

Grease

Cooling type

Aircooling

Bearings

2x7008c P4

2x7004c P4

 

VFD Specification:

Model

E550-4t0055L

Power (KW)

5.5KW

Input Voltage(V)

3-phase AC 380V ±20% 50/60Hz

Output Voltage(V)

0~380V

Output Current(A)

13A

Output Frequency (Hz)

0~1000Hz

Origin& Warranty&brand

China & One year&sunfar

1. electric spindle practices

Electric spindle is a high-speed high-precision components rigidity, we must strictly follow the practices used spindle spindle motor, otherwise it will increase equipment failures, shorten equipment life. Please use the rule as follows:

 (1) Before the boot, first ensure that the spindle cooling system to work properly, and then turn the power spindle. Do not use the spindle without the cooling conditions, it is necessary to check the fan and pump are working properly before use. If the spindle is water cooled, to check whether the cooling water containing impurities to ensure water is smooth.

(2) When using electric spindle, spindle from low according to the principle of high speed, gradually increasing speed to warm up, when the spindle load up to speed and smooth operation of the state after the required processing, can better protection spindle, to reduce the wear.

(3) during use is strictly prohibited beat, hit threaded spindle clamp and rotor end, so as not to reduce the component life, affect the results spindles used.

(4) During the operation, the tool must be replaced in the correct way. When the knife, the focus should be uniform, the tool should be aligned with the threaded end of the screw rotor, clamping can be. During operation the tool needs to be replaced before the replacement to wait Spindle cooling, avoid tool change at hot temperature state.

(5) During the operation, if the fixture card spindle rotor end, non-beat way to remove Jigs. Only under the premise of no damage to the rotor shaft threads with pliers and other tools to remove the chuck, and clean the rotor tapered bore and clamp the spindle to avoid Movies shorten life, affecting the quality of workpiece. If the fixture has completely lost precision, it must be replaced immediately.

2. The spindle maintenance specification:

 (1) to control the spindle actual time worked. Theoretically prohibit spindle 24 hours of continuous work, operating 12 hours per spindle Spindle let rest at least 2 hours, in order to prevent the formation of shortened due to mechanical fatigue life of the spindle.

 (2) to understand the conditions, the ambient temperature and the spindle temperature control. Spindle operating ambient temperature not higher than 35 centigrade degree, when the ambient temperature is above 35 centigrade degree should use air conditioners or other protective measures to reduce the room temperature, thereby reducing spindle temperature.

 (3) The spindle cooling water must be kept clean and free of impurities, recommendations to clean up after the end of the spindle shaft waterway, scale and water holes to avoid clogging due to rust. Also, always pay attention to circulating water temperature in the tank, so the water temperature is too high, the cooling effect can not be achieved prefetching.

(4) Always check the power supply connector, to avoid damage to the connector loose or aging brings to the spindle and the drive.

(5) If the downtime to use again, you must tranches from low speed to high speed spindle run-in steps according to the spindle load running, in order to use in the run-through.

(6) during the loading and unloading cutter knife, must tool chuck nut clean.

3. Use Caution

(1) must match the drive spindle chosen correctly according to the electric spindle nameplate good debugging power, voltage and frequency.

(2) Set the frequency converter should be set command channel, and then set the display channel, and finally set the parameters. When setting parameters, be sure that the reference frequency, the frequency of the three highest rated frequency and consistency.

(3) The spindle is generally clockwise in the wrong direction, the drive can change settings or swap any two rotating wire the inverter output UVW terminal on.

(4) In general, water-cooled spindle surface temperature and ambient temperature greater than 20 degrees, the heat can be considered a spindle; when air-cooled spindle surface temperature greater than ambient temperature of 30 degrees, can be identified as the main heat seriously, immediately shut down cooling, a check

4. Maintenance Caution

(1) Spindle found abnormal sound, should immediately stop checking. If you can not be resolved, should be sent to the manufacturer or repair to professionals.

(2) the operation of an abnormal burning smell, immediately stop checking. If you can not be resolved, should be sent to the manufacturer or repair to professionals.

(3) If the spindle does not run the boot, do not start over, you should carefully check the following related matters: first check the drive parameters to determine the input and output voltage, the spindle parameter settings are correct. Second, check the power cord and wiring connector is plugged in and determine whether the contact connector problem.

(4) Since the electric spindle is a high speed, high rigidity precision components and must therefore be sent back to me by professionals or for repair.

 

 

Shipping Policy

1. Item will be shipped out within 2-5 working days by DHL, FedEx, UPS, EMS and other shipping method you choose ASAP. We will choose the best and most suitable shipping company. Usually it takes 7-12 days to arrive most of the countries. You will be notified the tracking number once order shipped out.
2. International buyers are responsible for any customs fees and duties taxes for your local government. Please contact your local customs office with further inquiries on this issue. We will not be responsible for any tariffs, duties, or any other charges requested or required by destination countries..

About Us

The brand ToAuto belongs to the Fast To Buy Limited . We have specilized in professional CNC Solution for 6years , we can offer a complete series of Motors include Spindle Motor, Servo Motor, Stepper Motor , and has variety of CNC control parts and CNC Machine . Besides , we own a very professional CNC engineer team to help you offer any of CNC solutions .

 

Return Policy

1. We accept 14 days return policy. If you want to return the item, please contact us in 14 days first and make sure the package is un-opened. The buyer has to pay for the go and back delivery cost and the custom fee of each country. Once we received the product and checked, we will make refund for the part in 24 hours. 
2. We make sure the item is brand new with original package and offer 1 year warranty for the quality.
3. Any quality problem in normal use during the warranty period, We offer free repair. The buyer should pay the return cost and our company will pay the re-shipping cost.